欧美日韩毛片熟妇有码无码,亚洲欧美日韩久久精品第一区 ,国产AⅤ激情无码久久久无码,狂躁美女大bbbbbb视频

Welcome to [ Wuxi Funecon Precision Mould Plastic Co., Ltd. ] website! Home| Sitemap| Email
Moulding Your Future

Enquiry:

138-6185-1071

138-6185-1071

What are the main aspects of injection mold cooling water leakage

Injection mold cooling water leakage is a frequent occurrence, for many reasons, mainly in the following aspects:
The most occurs at the joint of the mold cooling water pipe. If water leakage is found, the sealing tape should be wound around the thread of the pipe joint and then tightened.
2, Due to long-term molding conditions, the waterproof ring inside the mold will be damaged, and the O-shaped waterproof rubber ring will easily harden and crack, resulting in water leakage. Some poorly installed waterproof rings can also cause seal failure. It is generally necessary to regularly check the installation position and sealing performance of the seal.
3, The hole wall of the cooling water hole is broken. This often happens when a new mold is tried. The wall thickness of the design is sufficient, but the hole wall is broken due to machining errors or post-processing. In most cases, leaking water holes can no longer be used.
4, Regularly repair the heating pipe and decompression pump and use. The heating tube is an effective heat transfer element and is very effective for core cooling of deep and deep structures. In the area where the cooling water is easy to pass, a one-way heating pipe is provided to reduce water leakage. In addition, the use of a vacuum pump to pump cooling water is also a method to prevent leakage of cooling water.
5, maintenance of the cooling water hole. It is easy to form scale in the cooling water hole, which hinders heat transfer. In severe cases, the water path is blocked and needs regular maintenance. For straight water holes, an iron bar that is 0.5 mm smaller than the diameter of the cooling water hole can be inserted and tapped with a hammer to remove scale and rust. For the cooling water pipe buried in the mold, the mold should be disassembled to remove rust.
After the inspection, the water leakage test should be carried out. The hand pressure pump is used to fill the water hole with water, and it is kept at a pressure of 2 MPa for 5 minutes. It is judged whether the water hole leaks by observing whether the water pressure is lowered. The water leakage can be blocked by mechanical fastening using elastic materials such as rubber and cork, and the room temperature curing type silica gel can be tried as a sealing material.
2018/08/02 10:11:16 6382 次

Hot News

Copy right of the 2018 Wuxi Funecon Precision Mould Plastic Co., Ltd. All Rights Reserved

无套内谢少妇毛片a片| 欧美一进一出抽搐大尺度视频| 人妻少妇精品无码专区动漫| 差差漫画在线观看登录页面弹窗 | 69久久夜色精品国产69| 国产男女猛烈无遮挡免费网站| 国产欧美va欧美va在线观看| 总裁把她的乳尖都吸大了| 99久久99久久精品国产片| 日本三级带黄在线观看| 人妻无码第一区二区三区| 中文字幕精品久久久久人妻| 东京热av人妻无码| 老板办公室乳摸gif动态图| 久久国产一区二区三区| 亚洲欧好州第一的日产suv| 亚洲va欧美va天堂v国产综合| 激情都市亚洲一区二区| 我和丰满岳疯狂做爰| 优优人体大尺大尺无毒不卡| 老头天天吃我奶躁我视频| 嫩草av久久伊人妇女超级a| 99久久综合狠狠综合久久| 午夜性刺激免费看视频| 99RE久久精品国产| 51精品国产人成在线观看| chinese叫床videos| 麻花传媒剧在线mv免费观看| 欧美最猛性xxx| 女人张开腿让男人添| 免费看大片的app| 精品国产精品久久一区免费式| 人妻无码熟妇乱又伦精品视频| 国产免费一区二区三区免费视频| 半夜洗澡被老头添一夜| 精品欧洲av无码一区二区三区| 天天做天天爱天天综合网2021 | 色窝窝亚洲av网在线观看| 免费网站看av片| 免费网站观看www免费下载| 免费看国产曰批40分钟|